|
Test |
|
Test Method |
|
Adhesion |
|
AA-P 177; ASTM D3359; BI 106-01; GM9071P; GMW14829; DIN 53151; JDQ 17; JDQ 139; JDH612#8; HOR10007#7; TSH 1551G-4.1, 4.2 and 4.3; MES MN 601-8; NES M0007-29; DBL 7399-5.1; HES D6501-3.6; DX900161; ISO 2409 |
|
Chip Resistance |
|
ASTM D3170; BI 157-04; GM9508P; GMW14700 (Method B&C); SAE J400; TS H1553G; JDQ 118; JDH612#11; MES MN 601-30; NES M0007-28; DBL 7399-5.3; HES D6501-3.33; BI 107-01; BI 157-06; DX900163; AA-P 192 |
|
Cure |
|
ASTM D5402, GM9509P, LP-463PB-31-01, HOR10007#10, TS H1551G-5.2, HES D6501-3.22, TS430-7, DX900120 |
|
Cyclic Corrosion |
|
AA-P 175; BI 123-01; BI 123-01 (manual); BQ104-07 (Method 1, Procedures 1-6); GM9511P; GM9505P (Cycle J); GM9540P (Automated/ Continuous Cabinet); GMW14872; LP463PB-22-01; LP-463PB-22-01 (Method II and IV); SAE J2334; VDA 621-415; Honda 5100Z-SEO-0000(Cyclic Corrosion);
NES M0007-33.4 and 46; DBL 7399-7.3; DX900119; DX900115; ISO 11997-1 (Cycle B) |
|
Film Thickness |
|
ASTM D7091 (Type 2-electronic); GM4260P (Except X-ray Fluorescence); BI 117-01; HES D6501-3.2.2;
JIS D0202-4.14; NES M0007-4.4.5 |
|
Fluids Exposure |
|
BI 113-05; BI 168-01; GM9501P; LP-463PB-31-01; JDQ 138; JDQ 142; JDH612#12; HOR10007#11; TS H1551G-7,-8 and -10 to -14; MES MN 601-19 and -24; NES M0007-36 to -39 and -43; DBL 7399-8.1 and 8.3; VDA 621-412; HES D6501-3.21, 3.23, 3.24 and 3.25; GMW14333; MG1004-151 |
|
Gloss |
|
ASTM D523; JDH612#4; HOR10007#3; NES M0007-21; HES D6501-3.3; BI 110-01; JDQ 12 |
|
Heat Resistance |
|
TS H1551G-9; JIS D0202-4.18 |
|
Humidity |
|
ASTM D1735, ASTM D2247, GM4465P, ISO 6270-2, section 6.4.2, JDQ 120, DIN 50017, NES M0007-32, HES D6501-3.19, JIS D0202-4.7, JDH612#2, HOR10007#2, DX900159; AA-P 224; GMW14729 |
|
Impact |
|
ASTM D2794; JDQ 117; JDH612#10; HOR10007#9; TSH 1551G-3; NES M0007-27; HES D6501-3.8 and 3.9; MES MN 601-35; ISO 6272-2 |
|
Mandrel Bend
(Conical & Cylindrical) |
|
ASTM D522, JDQ 116, JDH612#9, HOR10007#8, NES M0007-30, DBL 7399-5.5, HES D6501-3.10 & 3.11 |
|
Panel Evaluation |
|
ASTM D1654; ASTM D610; ASTM D714; GM9102P; GMW15282; DIN 53209; DIN 53167; DIN 50014; DIN 53210; DBL 7399-7.4.4; TSH 1550G-2.3.4; DX900027; ISO 4628-2; ISO 4628-3; ISO 4628-8; GMW15357 |
|
Pencil Hardness |
|
ASTM D3363, JDQ11, JDH612#7, HOR10007#6, TS H1539, MES MN 601-9, NES M0007-26, HES D6501-3.5, JIS D0202-4.13 (manual), GM9506P |
|
Salt Spray |
|
ASTM B117; JDH612#1; HOR10007#1; BI 103-01; GM4298P; TSH 1552G; JDQ 115; DIN 50021; DBL 7399-7.1; MES MN 601-27; NES M0007-33.3;
HES D6501-3.15; JIS Z2371; DX900158; GMW3286; ISO 9227 |
|
Thumbnail Hardness |
|
GM9507P |
|
Water/Salt Water Immersion |
|
ASTM D870, BI 104-01, BI 104-04, TS H1551G-6, MES MN 601-13, NES M0007-57, HES D6501-3.18, LP-463PB-31-01, MS-PB1-2-3.1.1 & 3.1.2, JIS K5400-7.2 |
|
Fluid Resistance, Cyclic Corrosion and Exposure Processing Per Individual Customer Specifications |
|
Acid, Alkali, Antifreeze, Brake Fluid, Gasoline, Diesel Fuel, Engine Oil, ATF, Water, Windshield Wiper Solvent, TSP, Hydraulic Oil, Gear Oil, Power Steering Fluid, Wax, Heat, Cold, Immersion, Salt Spray, Humidity, Solvent, Solvent Blends |